Knowledge Base
Answers to your most common questions
199 questions in 6 categories for 4 product series
Troubleshooting 5 questions
A slight change in the appearance or color of the AISI 304 stainless steel chamber after prolonged operation at high temperatures (approximately 250–300°C) is generally a normal result of heat exposure. This discoloration, often referred to as heat tint, is a surface phenomenon caused by the formation of a thin oxide layer and does not normally affect the oven's performance, durability, or corrosion resistance.
The discoloration is cosmetic and does not indicate a manufacturing defect or equipment malfunction. To help minimize changes in appearance, users should keep the chamber clean, promptly remove residues after use, and operate the oven within the recommended temperature range and according to the operating manual.
If the discoloration is accompanied by surface damage, corrosion, peeling, deformation, or abnormal performance, users should discontinue operation and contact an authorized DragLab service representative for technical evaluation.
A difference between the displayed temperature and the reading from an external thermometer can occur for several reasons and does not necessarily indicate a malfunction. Temperature readings may vary depending on the thermometer's accuracy, its location inside the chamber, response time, airflow patterns, and whether the oven has reached thermal equilibrium.
For the most accurate comparison, allow the oven to stabilize at the set temperature before taking measurements, position the reference thermometer near the center of the chamber without obstructing airflow, and avoid opening the door during the measurement process.
The DragLab Drying Oven Series features an adaptive programmable PID microprocessor controller and an automatically adjustable forced-air circulation system to maintain stable and uniform chamber temperatures. If a consistent difference remains after the oven has stabilized, users can utilize the built-in temperature calibration function to fine-tune the displayed temperature using a certified reference thermometer. If the discrepancy persists after calibration, contact an authorized DragLab service representative for technical assistance.
Slow heating can result from several operating conditions and does not necessarily indicate a fault with the oven. Common causes include a low supply voltage, frequent door openings, excessive sample loading, obstructed air circulation, or selecting a target temperature significantly higher than the ambient temperature.
To improve heating performance, ensure that the oven is connected to the correct power supply, avoid overloading the chamber, distribute samples evenly to maintain proper airflow, and keep the door closed during operation whenever possible. Adequate clearance around the oven should also be maintained to allow proper ventilation.
The DragLab Drying Oven Series uses an adaptive programmable PID microprocessor controller together with an automatically adjustable forced-air circulation system to achieve efficient, stable, and uniform heating. Under normal operating conditions, the oven typically reaches the set temperature within approximately 20 minutes, although the actual heat-up time may vary depending on the model, chamber size, set temperature, ambient conditions, and sample load.
If the oven continues to heat significantly more slowly than expected after these conditions have been checked, contact an authorized DragLab service representative for technical assistance.
Minor temperature fluctuations during heating are normal as the adaptive programmable PID microprocessor controller continuously regulates the heating elements to maintain the set temperature. However, larger or persistent temperature variations may result from frequent door openings, excessive sample loading, blocked air circulation, unstable power supply, or insufficient time for the chamber to reach thermal equilibrium.
To improve temperature stability, allow the oven to fully stabilize before starting temperature-sensitive procedures, keep the door closed during operation, distribute samples evenly without obstructing the airflow, and avoid exceeding the recommended chamber load. Proper installation with adequate ventilation and a stable power supply also contributes to consistent performance.
The DragLab Drying Oven Series combines an automatically adjustable forced-air circulation system with an adaptive PID controller to maintain excellent temperature uniformity (typically within ±1°C under normal operating conditions) and stable heating throughout the chamber.
If excessive temperature fluctuations continue after verifying these operating conditions, check the temperature calibration using a certified reference thermometer. If the issue persists, contact an authorized DragLab service representative for technical assistance.
A small amount of warmth around the door area during operation is normal, especially when the oven is operating at elevated temperatures. However, excessive heat leakage may indicate that the door is not fully closed, the synthetic rubber door gasket is damaged, worn, contaminated, or improperly seated, preventing an effective seal.
To ensure proper sealing, verify that the door is completely closed and latched, inspect the gasket for signs of wear, cracks, deformation, or contamination, and clean both the gasket and the door sealing surface regularly using a soft, non-abrasive cloth. If the gasket is damaged, it should be replaced with a genuine DragLab replacement gasket to restore optimal sealing performance.
A properly sealed door helps maintain stable chamber temperatures, minimizes heat loss, improves energy efficiency, and ensures uniform heating throughout the chamber. If excessive heat leakage continues after inspecting the door and gasket, discontinue use and contact an authorized DragLab service representative for technical assistance.
Check the spelling, try a different term or choose another category above. Or ask us directly: +49 6196 400816, info@drag-lab.de.
Planning a purchase?
Send us your request. We will prepare a quote and help you choose the right device.